Jul 27, 2013 As in my other post about a wood stove for my greenhouse. I have a V C Intrepid II with 1987 stamped on the inside of the stove. I have searched on the net for a owners manual with no luck.
CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, without notice.
Item Description
Part Number
Item Description
Part Number
Intrepid II Woodburning Stove
Model 1990CE (continued)
24. Air Flap Pin
Intrepid Ii Wood Stove Parts
1601551
25. Clip
1601396
26. #10-24 x 3/8” Pan Head Bolt
1200983
27. #10-24 x 1/4” Pan Head Bolt
1200980
28. Secondary Probe Assembly
1601489
29. Secondary Air Link
1601486
30. Phillips Bolt, 1/4”-20 x 5/8”
1200896
31. Shim Ring
1201986
32. Secondary Air Flap
1601490
33. Refractory Chamber w/ Access Panel
1602527
34. Catalyst Block
30001153
35. Refractory Access Panel
1602516
36. Andiron
1306717
37. Left Insert
1308651
38. Grate
1308652
39. Right Insert
1308650
40. Ashpan Only
1400951
41. Ashpan Front Only
1306493
42. Ashpan Handle
30000973
43. Damper Tab
1601488
44. Griddle
1306356
45. Right Griddle Quad
1301832
Advertising
Popular Brands
Popular manuals
Advertising
9
Intrepid II Woodburning Stove
30003840
Costructional Hearth
Dimensions as below
At least 300 mm
At least 150 mm
Intrepid 2 Wood Stove Manual
or to a suitable
heat resistant wall
At least
150 mm
Hearth Surface
Free of Com-
bustible Material
Perimeter should be
clearly marked e.g.
edge of superimposed
hearth
Perimeter should be
clearly marked e.g.
edge of superimposed
hearth
Appliance
Doors
Torch so uniqe, they combine browser, media player and sharing features. Torch browser manual download for windows 7. What make it more special is They are really Free. No money needed to install this software.For torrent downloader use this browser will make them falling in love with torch, cause you will allow to direct download torrent and maange it by this browser.
Appliance
Doors
ST912
Fig. 10 Noncombustible hearth surface dimensions.
a) Fireplace recess
b) Free standing
Floor Protection for Fireplace Installations
Do not assume your fireplace hearth is completely noncombustible. Many fireplace hearths do not satisfy the “completely noncombustible” requirement because the brick or concrete in front of the fireplace opening is supported by heavy wood framing as in Figure 9. Because heat passes through brick or concrete readily, it can easily pass through to the wood. As a result, such fireplace hearths can be a fire hazard and are considered a com- bustible floor. Keep in mind that many raised hearths will extend less than the required clearance from the front of the heater when it is installed. In such cases, sufficient floor protection as described above must be added in front of the hearth to satisfy the minimum floor protector requirement from the front of the stove: 406 mm (16”) from the front. Fireplace hearths must also offer the required protection of 152 mm (6”) on either side. Optional 76 mm (3”) short legs may be used only on such hearths that meet the width and depth require- ments outlined previously under “floor protection.” Hearth rugs do not satisfy the requirements for floor protection. Fireplace installations also have special clearance requirements to the side walls, side decorative trim, and fireplace mantle. Refer to the information on fireplace and mantel trim shields in this section.
Keep the Stove a Safe Distance from
Intrepid 11 Wood Stove
Surrounding Materials
Both a stove and its chimney connector radiate heat in all directions when operating, and dangerous overheat- ing of nearby combustible materials can occur if they
Intrepid Ii Manual
are too close to the heat. A safe installation requires that adequate clearance be maintained between the hot stove and its connector and nearby combustibles. Clearance is the distance between either your stove (measured from the back edge of the stove’s top plate) or chimney connector, and nearby walls, floors, the ceiling, and any other fixed combustible surfaces. In addition, furnishings and other combustible materials must be kept away from the stove as well. In general, a distance of 1220 mm (48”) must be maintained between the stove and moveable combustible items such as dry- ing clothes, furniture, newspapers, firewood, etc. Keep- ing those clearance areas empty assures that nearby surfaces and objects will not overheat.
Clearances
Intrepid Wood Stove Manual
As with any solid fuel heating stove, extremely high surface temperatures can occur, particularly in the event of uncontrolled operation, e.g. if the doors are inadvertently left open. It is crucial that suf- ficient clearances are allowed to any combustible surfaces, e.g. wooden mantels or lintels, and to timber framed (studded) walls even if they are faced with noncombustible board. Detailed information on fireplace and hearth construction is provided in section 2 of Document J, all installations must comply with these requirements or with the relevant National or local building standards. Clearances to timber framed (studded) walls are includ- ed below. There are no specific minimum clearances to solid noncombustible surfaces (e.g. the sides and rear of Inglenook fire openings constructed from solid masonry) other than to allow safe access to the controls of the stove. For this reason minimum side clearances of 125 mm, and a minimum rear clearance of 50 mm are recommended.